In electronics, crosstalk is any phenomenon by which a signal transmitted on one circuit or channel of a transmission system creates an undesired effect in another circuit or channel. Crosstalk is usually caused by undesired capacitive, inductive, or conductive coupling from one circuit or channel to another.
In structured cabling, crosstalk refers to electromagnetic interference from one unshielded twisted pair to another twisted pair, normally running in parallel. Signals traveling through adjacent pairs of wire interfere with each other. The pair causing the interference is called the “disturbing pair”, while the pair experiencing the interference is the “disturbed pair”.
- Near end crosstalk (NEXT)
- NEXT is a measure of the ability of a cable to reject crosstalk, so the higher the NEXT value, the greater the rejection of crosstalk at the local connection. It is referred to as Near End because the interference between the two signals in the cable is measured at the same end of the cable as the interfering transmitter. The NEXT value for a given cable type is generally expressed in decibels per feet or decibels per 1000 feet and varies with the frequency of transmission. General specifications for cabling (such as CAT 5) usually include the minimum NEXT values.
- Power sum near end crosstalk (PSNEXT)
- PSNEXT is a NEXT measurement which includes the sum of crosstalk contributions from all adjacent pairs as an algebraic sum of the NEXT of the three wire pairs as they affect the fourth pair in a four-pair cable (e.g., Category 6 cable). The Superior Modular Products White paper states that the testing process for PSNEXT consists of measuring all pair-to-pair crosstalk combinations and then summing all of the values for each pair. The specification was developed to directly address the effect of transmissions on multiple adjacent pairs on the pair being tested and is relevant to all connecting hardware and associated communications cables.
- Cabling bandwidths in excess of 100 MHz (Category 5 cable bandwidth) make consideration of PSNEXT more important as Gigabit Ethernet through Cat-6 uses all four wire pairs simultaneously and bidirectionally. The additional wire pair usage and growing bandwidth increases the need to keep NEXT in check.
- Far end crosstalk (FEXT)
- FEXT measures the interference between two pairs of a cable measured at the far end of the cable with respect to the interfering transmitter.
- Equal level far end crosstalk (ELFEXT)
- ELFEXT measures the FEXT with attenuation compensation.
- Alien crosstalk (AXT)
- AXT is interference caused by other cables routed close to the cable of interest as opposed to signals contained in the same cable.
In stereo audio reproduction, crosstalk can refer to signal leaking across from one program channel to another, reducing channel separation and stereo imaging. Crosstalk between channels in mixing consoles, and between studio feeds is a much more noticeable problem, as these are likely to be carrying very different programmes or material.
Crosstalk is an electrical effect and can be quantified with a crosstalk measurement. Crosstalk measurements are made on audio systems to determine the amount of signal leaking across from one channel to another. The Independent Broadcasting Authority published a weighting curve for use in crosstalk measurement that gives due emphasis to the subjective audibility of different frequencies. In the absence of any international standards, this is still in use despite the demise of the IBA.
Good crosstalk performance for a stereo system is not difficult to achieve in today's digital audio systems, though it was hard to keep below the desired figure of -30 dB or so on vinyl recordings and FM radio.
In telecommunication or telephony, crosstalk is often distinguishable as pieces of speech or in-band signaling tones leaking from other people's connections. If the connection is analog, twisted pair cabling can often be used to reduce crosstalk. Alternatively, the signals can be converted to digital form, which is typically less susceptible to crosstalk.
In integrated circuit design, crosstalk normally refers to a signal affecting another nearby signal. Usually the coupling is capacitive, and to the nearest neighbor, but other forms of coupling and effects on signal further away are sometimes important, especially in analog designs. See signal integrity for tools used to measure and prevent this problem, and substrate coupling for a discussion of crosstalk conveyed through the integrated circuit substrate. There are a wide variety of repair solutions, with increased spacing, wire re-ordering, and shielding being the most common.
In full-field optical coherence tomography, "crosstalk" refers to the phenomenon that due to highly scattering objects, multiple scattered photons reach the image plane and generate coherent signal after traveling a pathlength that matches that of the sample depth within a coherence length.
In stereoscopic 3D displays, "crosstalk" refers to the incomplete isolation of the left and right image channels so that one leaks or bleeds into the other - like a double exposure, which produces a ghosting effect.
- Attenuation-to-crosstalk ratio
- Audio system measurements
- Co-channel interference (CCI)
- Signal integrity
- Signal-to-interference ratio (SIR or S/I), also known as carrier-to-interference ratio (CIR or C/I)
- Substrate coupling
- Unger model
- "Category 5 / 5E & Cat 6 Cabling Tutorial and FAQ's". lanshack.com. Archived from the original on 2013-01-17. Retrieved 2013-01-05.
- "Component Level PowerSum Compliance and RJ21X Connectivity Solutions (Superior Modular Products White paper)" (PDF). Archived from the original (PDF) on July 16, 2006. Retrieved 2008-09-13.
- Eliminating alien crosstalk, Communications News, February 2009, archived from the original on 2010-02-09
- "crosstalk (XT)". Federal Standard 1037C glossary. Retrieved 2018-03-26.
|Look up crosstalk in Wiktionary, the free dictionary.|